top of page

EU MCCP POPs Restriction: 0.1% Limit from 16 Dec 2026

15 hours ago
4 min read

EU MCCP POPs Restriction: Regulation 2026/2035 Bans MCCPs in Articles and Electronics from 16 December 2026


The EU MCCP POPs restriction is now law. Commission Delegated Regulation (EU) 2026/2035, adopted on 11 September 2026 and published in the Official Journal on 18 November 2026, adds medium-chain chlorinated paraffins (MCCPs) to Part A of Annex I to the POPs Regulation, Regulation (EU) 2019/1021. It applies from 16 December 2026, less than a month away.


Background: from the Stockholm Convention to EU law


The Stockholm Convention's Conference of the Parties decided at its twelfth meeting, from 28 April to 9 May 2025, to list MCCPs in Annex A with specific exemptions. The EU supported that listing, and the POPs Regulation is how the Union puts it into effect. ECHA's risk assessment and socio-economic committees had already backed a restriction on MCCPs under REACH in 2023.

Substances in Part A of Annex I fall under Article 3 of the POPs Regulation, which prohibits their manufacture, placing on the market and use on their own, in mixtures or in articles. For electronics makers, articles are the point: a cable, housing or seal that contains MCCPs is covered.


Key Changes in the EU MCCP POPs Restriction


What counts as MCCPs

The entry covers substances or mixtures containing linear C14–C17 chloroalkanes with set minimum chlorination (five or more chlorine atoms for C14 and C15, six or more for C16 and C17). CAS numbers include 85535-85-9, 198840-65-2 and 1372804-76-6, "and others".


Trace limit

MCCPs present as an unintentional trace contaminant are allowed up to 1,000 mg/kg (0.1% by weight) in substances, mixtures or articles. Above that, the prohibition applies. Recovered material from cable recycling can contain up to 2% until 16 December 2028, but only when it's used in road furniture or blocks that support fences.


Illustration of a technician testing an electronic device housing with flexible cables in a laboratory under a circle of European Union stars.

Exemptions with end dates

The exemptions are narrow. Those most relevant to electrical products are:


  • flexible PVC in wires and cables for the construction sector, until 16 December 2028

  • flexible PVC in wires and cables in medical devices and in vitro diagnostic (IVD) devices, until 16 December 2031

  • polymers and rubbers in spare parts for, and repair of, EEE for medical and IVD devices and instruments for measurement, analysis, control, monitoring, testing and inspection, where MCCPs were used originally, until the end of service life or 31 December 2041


Other exemptions cover heavy-duty metalworking fluids (until 31 December 2036), door and window sealants, waterproof and anti-corrosion coatings, and several aerospace, defence and ammunition uses.

There's no general exemption for consumer or IT electronics. Articles already in use when an exemption ends can stay in use, and spare parts present in the EU before 1 January 2042 can still be sold and used.


Supplier information

Manufacturers, suppliers and importers of chlorinated paraffins must state the MCCP content in the Safety Data Sheet. Where it's above 0.1%, they must also give risk management measures. The content has to be measured with validated analytical methods on representative batches.


What This Means for Manufacturers


  • Any EEE sold in the EU from 16 December 2026 must not contain MCCPs above 0.1%, unless a listed exemption applies.

  • The exemptions show where MCCPs tend to appear: flexible PVC wires and cables, sealants, coatings, and polymers and rubbers. Those materials need checking first.

  • Cables are the likeliest risk. Only construction-sector and medical cables have a grace period.

  • Supplier declarations should cover MCCPs explicitly, since many existing material declarations won't list them.

  • Where declarations are unclear, chemical testing of PVC and rubber parts can confirm content below 0.1%.

  • The regulation sets no general transition period for products already in the supply chain, so stock that will still be on sale after 16 December 2026 needs review.


Certification Impact Summary


Area

Before

After

Impact level

MCCPs under the POPs Regulation

Not listed in Annex I

Listed in Part A; manufacture, placing on the market and use prohibited

High

Articles (cables, housings, seals)

No POPs limit

0.1% (1,000 mg/kg) trace limit

High

Flexible PVC cables, construction

No POPs limit

Allowed until 16 December 2028

Medium

Flexible PVC cables, medical and IVD devices

No POPs limit

Allowed until 16 December 2031

Medium

Spare parts for listed equipment

No POPs limit

Allowed until end of service life or 31 December 2041

Low

Supplier documentation

No MCCP-specific duty

MCCP content in Safety Data Sheets

Medium


Timeline and Required Actions


Key Dates


Date

Milestone

28 April – 9 May 2025

Stockholm Convention lists MCCPs in Annex A

11 September 2026

Commission adopts Delegated Regulation (EU) 2026/2035

18 November 2026

Published in the Official Journal

8 December 2026

Entry into force

16 December 2026

Prohibition applies

16 December 2028

Construction cable, sealant and coating exemptions end; 2% recycled-cable limit ends

16 December 2031

Medical and IVD cable exemption ends

31 December 2041

Latest end of the spare-parts exemption


Required Actions for Manufacturers


  1. List the PVC, rubber, sealant and coating materials in every product sold in the EU.

  2. Ask suppliers to declare MCCP content against the 0.1% limit.

  3. Test materials where declarations are missing or unclear.

  4. Check whether any product relies on an exemption, and note its end date.

  5. Update restricted-substance lists and supplier contracts to name MCCPs.

  6. Review stock that will still be on sale after 16 December 2026.


Conclusion


The EU MCCP POPs restriction applies on 16 December 2026, and it reaches into ordinary components such as PVC cables and rubber parts. With only narrow, dated exemptions, the safest route is to confirm MCCP content now. We can help you plan supplier declarations and material testing for the EU market. Contact us at contact@gmalabs.com.


bottom of page