top of page

China GB 9159 Radio Transmitter Safety: MIIT Draft

11 hours ago
3 min read

China GB 9159 Radio Transmitter Safety: MIIT Drafts Mandatory Update, Comments Due 27 Dec 2026


China GB 9159 radio transmitter safety requirements are up for revision. On 28 October 2026, the Ministry of Industry and Information Technology (MIIT) published a draft of the mandatory national standard "Safety requirements for radio transmitting equipment" for public comment. It would replace GB 9159-2008. Comments are open from 29 October to 27 December 2026.


Background


GB 9159 was first published in 1988 and last revised in 2008. According to MIIT's explanatory note, the current version is used in testing for broadcast and medium- and short-wave communication transmitters and in related production licensing. The note says the old text no longer covers newer equipment, such as BeiDou ground-based augmentation transmitters. It also says transmitters are increasingly installed in cities and near homes, not just in remote sites.

The revision is led by the China Electronics Standardization Institute (CESI) under project plan No. 20256703-Q-339, and it references IEC 60215:2016. All of its technical content would be mandatory.


Infographic summarizing the draft update to China’s mandatory radio transmitter safety standard (GB 9159) issued by MIIT, highlighting public comment dates (29 October–27 December 2026), key technical changes for manufacturers—Chinese markings, battery restrictions, laser safety, and RF exposure/temperature limits—and a four-step compliance action plan.

Key Changes in the China GB 9159 Radio Transmitter Safety Standard


Scope

The draft applies to radio transmitting equipment operated by skilled personnel. It also covers auxiliary equipment that's part of a transmitter system, such as combining units, matching networks and cooling systems. It doesn't apply to antenna systems, feeders or matching networks outside the transmitter, or to Class II transmitters with double or reinforced insulation and no protective earth.


New and revised requirements

  • A new chapter on safety principles, plus revised normal-use conditions (+5 °C to +45 °C, 45–75% relative humidity, 86–106 kPa) and revised single-fault conditions.

  • Equipment must not contain batteries with more than 0.005% mercury by weight, and portable batteries with more than 0.002% cadmium are excluded. Batteries need disposal markings, and replaceable lithium-type cells need an explosion warning.

  • Optical fibre links should use Class 1 lasers. Equipment with Class 1M or higher must meet GB/T 7247.12. Lasers need labelling under GB/T 7247.1, and Class 3 and 4 lasers need interlocks.

  • Safety markings must use Chinese characters, as must service and safety instructions. Markings need to survive a rub test with water and petrol.

  • Hazardous substances may not exceed the limits in GB 26572 unless exempted.

  • Stray electric and magnetic fields in the operator area must stay within the limits in Annex D, which references ICNIRP guidelines. A new Annex F sets contact temperature limits.

  • The draft also adds rules on self-tapping screws, earthing of cables and hooks, and three-phase supplies with single-phase breakers.


What This Means for Manufacturers


Makers of broadcast, communications, navigation and other professional transmitters that sell into China should compare their designs with the draft now. Battery chemistry, laser modules, Chinese-language labels and manuals, and exposure documentation are the areas most likely to need work.

The explanatory note proposes a 12-month transition after approval. It also says that, under China's radio transmitting equipment rules, non-compliant equipment shouldn't be produced, sold, registered or used in China. MIIT would supervise the standard, and the note recommends notifying it to the WTO.


Certification Impact Summary


Area

Before (GB 9159-2008)

After (draft)

Impact level

Standard status

Mandatory

Mandatory; all technical content mandatory

Medium

Batteries

Installation and ventilation rules

Mercury and cadmium caps, disposal marking, explosion warning

High

Optical fibre and lasers

No specific requirement

Class 1 lasers for fibre; GB/T 7247 labelling and interlocks

Medium

Markings and manuals

Safety markings required

Chinese characters, durability test, Chinese instructions

Medium

RF exposure

Non-ionizing radiation requirement

Operator-area limits per Annex D (ICNIRP)

Medium

Contact temperatures

No annex

New Annex F limits

Medium

Transition

Not applicable

Proposed 12 months after approval

To be confirmed


Timeline and Required Actions


Key Dates


Date

Milestone

December 2025

Standard project approved by SAC

28 October 2026

MIIT publishes the draft for comment

27 December 2026

Comment period ends (page header: 26 December)

To be confirmed

Approval and publication by SAMR and SAC

To be confirmed

In force, proposed 12 months after approval


Required Actions for Manufacturers


  1. Check whether your transmitters and auxiliary units fall within the draft scope.

  2. Review batteries, laser modules and fibre links against the new requirements.

  3. Prepare Chinese-language safety markings and service instructions.

  4. Check operator-area field strengths against the ICNIRP-based limits.

  5. Send comments on the MIIT feedback form to kjbz@miit.gov.cn before the deadline.

  6. Plan redesign and retesting around the proposed 12-month transition.


Conclusion


The draft China GB 9159 radio transmitter safety standard modernises a 2008 text with requirements on batteries, lasers, markings, exposure and temperature. It's still a draft, so now is the time to compare designs and comment. GMA Labs can review your transmitters against the draft and follow it through to publication.


bottom of page